What are the symptoms of Bertazzoni Dishwasher Error Code E9?

Dishwasher fails to start or stops mid-cycle No water or insufficient water inside the wash chamber Error code E9 displayed on the control panel Fill cycle takes longer than normal Audible clicking or buzzing from the water inlet valve area Dishwasher beeps repeatedly when attempting to run a cycle

What can I safely check before calling a technician for Bertazzoni Dishwasher Error Code E9?

Check the circuit breaker panel and ensure the breaker serving the dishwasher is in the ON position; flip it OFF then back ON if tripped Verify the main water supply valve under the sink is fully turned on (should turn counterclockwise until fully open) Inspect both ends of the water inlet hose for kinks, twists, or pinching; straighten any bends carefully Disconnect the inlet hose at the wall connection and briefly run water into a bucket to ensure adequate water pressure Check if the inlet hose has ice buildup (in cold climates) and allow it to thaw naturally Remove and inspect the inlet hose filter screen for debris or sediment; rinse under clean running water if clogged Open the dishwasher door fully and listen for any unusual sounds when attempting to start a cycle Ensure the dishwasher door is closing completely and latching properly until you hear a click Power reset the dishwasher by turning off the breaker for 60 seconds, then turning it back on Run a short test cycle to determine if error E9 clears after reset If error persists after these checks, contact a certified Bertazzoni service technician for inlet valve replacement

Error Detected May 1, 2026

Error Code

Bertazzoni Dishwasher Error Code E9

Error code E9 on Bertazzoni dishwashers indicates a water inlet or fill system malfunction. This error means the dishwasher is unable to detect proper water flow or pressure during the fill cycle, preventing normal operation.

Book a Repair Ask an Expert

Quick Diagnostics

Signs 6 identified

Possible Causes 9 listed

Safety Checks 11 steps

If unsure, stop using the appliance and contact a certified technician immediately.

01

• Dishwasher fails to start or stops mid-cycle
02

• No water or insufficient water inside the wash chamber
03

• Error code E9 displayed on the control panel
04

• Fill cycle takes longer than normal
05

• Audible clicking or buzzing from the water inlet valve area
06

• Dishwasher beeps repeatedly when attempting to run a cycle

• Kinked or pinched water inlet hose restricting water flow

• Clogged inlet valve filter screens (due to sediment in USA water supply)

• Water supply valve partially or fully closed at wall connection

• Faulty water inlet valve solenoid

• Low water pressure from main supply line

• Malfunctioning water level sensor or float switch

• Frozen or blocked inlet hose during cold weather

• Electrical connection issue with the fill valve (120V circuit problem)

• Circuit breaker tripped affecting the inlet valve power supply

1

• Check the circuit breaker panel and ensure the breaker serving the dishwasher is in the ON position; flip it OFF then back ON if tripped
2

• Verify the main water supply valve under the sink is fully turned on (should turn counterclockwise until fully open)
3

• Inspect both ends of the water inlet hose for kinks, twists, or pinching; straighten any bends carefully
4

• Disconnect the inlet hose at the wall connection and briefly run water into a bucket to ensure adequate water pressure
5

• Check if the inlet hose has ice buildup (in cold climates) and allow it to thaw naturally
6

• Remove and inspect the inlet hose filter screen for debris or sediment; rinse under clean running water if clogged
7

• Open the dishwasher door fully and listen for any unusual sounds when attempting to start a cycle
8

• Ensure the dishwasher door is closing completely and latching properly until you hear a click
9

• Power reset the dishwasher by turning off the breaker for 60 seconds, then turning it back on
10

• Run a short test cycle to determine if error E9 clears after reset
11

• If error persists after these checks, contact a certified Bertazzoni service technician for inlet valve replacement

Always unplug the appliance before performing any physical check. These are visual/external checks only.

Still having trouble?

Our certified technicians diagnose and fix this error code permanently.

Schedule a Repair Call Us Now

Bertazzoni Dishwasher Error Code E9

Signs

Possible Causes

Safety Checks You Can Do