What are the symptoms of Bertazzoni Dishwasher Error Code E6?

Dishwasher fails to fill with water during the wash cycle Cycle stops prematurely or does not start E6 error code displays on the control panel Audible clicking or buzzing sounds from the inlet valve area Dishes remain dry after a complete cycle Water drains immediately after partial fill Dishwasher runs but produces no cleaning action

What can I safely check before calling a technician for Bertazzoni Dishwasher Error Code E6?

Check that the circuit breaker for your dishwasher is in the ON position; reset if tripped by switching OFF then ON Verify the home water supply valve (under the sink) is fully turned on by rotating the knob counterclockwise Inspect the inlet hose behind the dishwasher for visible kinks, twists, or pinches and straighten carefully Ensure the inlet hose connection fittings are hand-tight at both the dishwasher and water supply valve Turn off water supply at the valve, then disconnect the inlet hose and check the inlet filter screen for debris or sediment; rinse clean with running water Verify the dishwasher door is closing completely and the latch engages properly until you hear a click Press and hold the START button for 3 seconds to cancel the current cycle Power down the entire dishwasher by switching OFF the circuit breaker for 60 seconds, then switch back ON to reset the control board Run a short test cycle to see if the error clears Contact Bertazzoni USA customer service or a licensed appliance technician if error persists after these checks

Error Detected May 1, 2026

Error Code

Bertazzoni Dishwasher Error Code E6

Error code E6 on Bertazzoni dishwashers sold in the USA typically indicates a water inlet or fill system malfunction. This error means the dishwasher is not receiving adequate water supply or detecting a problem with the water inlet valve during the fill cycle.

Book a Repair Ask an Expert

Quick Diagnostics

Signs 7 identified

Possible Causes 10 listed

Safety Checks 10 steps

If unsure, stop using the appliance and contact a certified technician immediately.

01

• Dishwasher fails to fill with water during the wash cycle
02

• Cycle stops prematurely or does not start
03

• E6 error code displays on the control panel
04

• Audible clicking or buzzing sounds from the inlet valve area
05

• Dishes remain dry after a complete cycle
06

• Water drains immediately after partial fill
07

• Dishwasher runs but produces no cleaning action

• Water inlet valve malfunction or failure

• Clogged inlet water filter screen (debris from supply line)

• Kinked or pinched inlet hose restricting water flow

• Low water pressure from home supply line (below 20 PSI)

• Circuit breaker tripped affecting 120V power to inlet valve

• Frozen inlet line (in cold climates or unheated spaces)

• Faulty water level sensor

• Broken or disconnected inlet hose connection

• Control board communication error with inlet valve

• Mineral buildup in inlet valve from hard water

1

• Check that the circuit breaker for your dishwasher is in the ON position; reset if tripped by switching OFF then ON
2

• Verify the home water supply valve (under the sink) is fully turned on by rotating the knob counterclockwise
3

• Inspect the inlet hose behind the dishwasher for visible kinks, twists, or pinches and straighten carefully
4

• Ensure the inlet hose connection fittings are hand-tight at both the dishwasher and water supply valve
5

• Turn off water supply at the valve, then disconnect the inlet hose and check the inlet filter screen for debris or sediment; rinse clean with running water
6

• Verify the dishwasher door is closing completely and the latch engages properly until you hear a click
7

• Press and hold the START button for 3 seconds to cancel the current cycle
8

• Power down the entire dishwasher by switching OFF the circuit breaker for 60 seconds, then switch back ON to reset the control board
9

• Run a short test cycle to see if the error clears
10

• Contact Bertazzoni USA customer service or a licensed appliance technician if error persists after these checks

Always unplug the appliance before performing any physical check. These are visual/external checks only.

Still having trouble?

Our certified technicians diagnose and fix this error code permanently.

Schedule a Repair Call Us Now

Bertazzoni Dishwasher Error Code E6

Signs

Possible Causes

Safety Checks You Can Do